Xhorse VVDI2 VAG and Audi A4 2002 RB4 cluster

2002 Audi should be RB4 and at least in North America do not require a dealer pre-programmed key, it adds the 7 byte CS to the key the first time it is programmed (must be virgin id48 or id48 audi can chip if not a key already programmed to the car before).

If you can re-enable the immobilizer try with the pincode using vcds or similar tool. Watch out for lock times, could have been the cause in the first place. It should also only have a 4-digit skc (plus leading zero), so keep that in mind. At least in North America I have not seen an RB8 cluster before 2005.5 (not sure if it can be retrofitted but have not seen one from the factory that way)

 

To check if it’s non or crypto, the case on RB4 cluster has simple solutions with Pin. If you get 5 digit pin you have NONE crypt cluster. Also you can compare Immo block with Crypt one and there will be big difference.I always said , it is not tool that makes perfect job , it is person who using it.
When you read cluster there will never be damage.
Damage comes with writing.

 

To deal the dash with vvdi2 auto detect , sometimes it works but sometimes it doesn’t . i just find out that its not working most the times. I’ve done many and they have worked but this car didn’t. so i guess like the members here said , get pin code from ECU and adapt it with VCDS

 

 

NOTE:

can’t simply get another dump, then make it virgin, then use the pin from ecu + vcds to adapt the dash.

VAG 48 chip keys copy using VVDI2

Xhorse VVDI2 VAG key programmer can copy 48 transponder, without binding a Condor Mini key cutting machine.

 

 

Vvdi vag 1.2.6 download on Mega:

https://mega.nz/#!2lRTTL4C!FY847AYSd3ASGbS3b2Wh5EQr53foU4u96xngbefsItY

Require vvdi2 firmware v2.2.5

 

Run VVDI2 VAG software

Select Key learn in the menu

Then 4th immobilizer system – copy 48 transponder:

Step 1

Copy 48 procedure require PIN and component security bytes from cars

Select Get component security from engine control unit via obdii

 

Step 2

Connect the emulator to VVDI2 commander and switch ON ignition with the emulator, switch OFF/ON for 3 times

(attention: it requires OBD when lost all key)

 

Step 3

Decode the collected data via internet, and save the “calculate 48 data”. You can copy/prepare key with “calculate 48 data”

(attention: every success calculation will cost 100 remote points)

 

Step 4

Learn the new key with “calculate 48 data”. If the key was made by copy, it can start engine without learn

 

[Note 1] About new adapter Vvdi2:

some nec24c32 nec24c64 nec35XX all key lost not need remove instrument.(need read cs from ecu).

 

[Note 2] About copy 48 function on VVDI2:
(1) Authorize copy 48 function require 1000 remote points, require buy an extra emulator
(2) You can exchange it with “Transponder Programmer -> Menu -> Points System”
(3) Every success calculate will cost 100 remote points
(4) Copy 48 fucntion use in 4th immobilizer system(Dashboard), support type: NEC24C32, NEC24C64, NEC24C64 colordisplay, A1, A3/TT/R8, Q3, New tiguan 5ND920873B, 5ND920883B etc
(5) Copy 48 fucntion can work on the car that which support read PIN and CS via OBDII. Ofcourse, known CS and PIN is supported. Support make new key, support add keyless GO keys, especially support lost all key
(6) For Passat B6/CC only support clone 48 transponder(must have working key), don’t support 46 transponder, dont support keyless Go, dont support lost all key

VVDI2 Copy VAG 48 Transponder Function Authorization:

http://www.xhorsetool.com/wholesale/vvdi2-vag-copy-48-function.html

Condor XC mini Update Tool 1.0.9 Free Download

Free download ikeycutter condor xc-mini update tool v1.0.9 on Mega:

Condor XC-Mini update tool 1.0.9Km03.zip

condor key cutting machine key data customize tool:

Update steps:

Do not turn off or unplug USB cable during updating

If the update fails, turn off anti-virus software and then try again.

1- connect keymachine to pc with a usb cable

2- turn in the keymachine

3- click on the “update online” button to start update

4- the screen will appear “updating” prompt

5- update complete

 

Why is the condor mini update tool used for?

Device info

Active

Fix data error (picture list, ect.)

Fix “internal error 1” error

Enter BIOS mode

Clear all data (need redo: cut_calibrate, x1 init and x2 init)

Select clamp

Offline update

Create file

Fix “internal error 2” error

History record