Xhorse Multi-Prog Tag Archive
Xhorse Multi Prog Cannot Write Jeep Renegade R7F701056 BCM Solution
Customer problem: I wanted to write Dflash data on a 2017 Jeep Renegade with R7F701056 BCM using Xhorse Multi Prog, but I did not find the write option in the software. Solution: Please select R7F701056 (RENESAS-> RH850) in Multi-Prog software, and you will see the related operation option. Tech support: Email: Sales@xhorseTool.com Whatsapp/Tel:+86 15387077565 Business […]
How to Connect Xhorse Multi-Prog and SOP44 Adapter?
To connect Xhorse Multi-Prog programmer to an SOP44 adapter (such as the VH24 or VH30 adapter board), you need to swap the internal default adapter board inside the device. Step-by-Step Connection Guide 1.Open the Device: Remove the magnetic shield on the top of Multi-Prog unit. Unscrew the four screws securing the default VH13 interface adapter board that […]
How to Fix Xhorse Multi-Prog “Failed to Execute VPA” Error (040510C)?
Problem: When using Xhorse Multi-Prog to communicate with a BMW X1 series Bosch MEVD17.2.4 (N20) ECU, the device fails to establish communication, and the gray wire (P1) outputs no frequency signal. Error Message: Failed to execute VPA. Error code: 040510C – Unknown error type. Resolution Steps Update Software: Contact customer support to download and install […]
Xhorse Multi Prog BMW BDC2 BDC3 LCD Encrypted Key Pinouts
Xhorse Multi-Prog Programmer has been updated to read original data from BMW BDC2, BDC3, and LCD encrypted keys. For unencrypted Hungary BDC3 keys: Multi Prog reads the data directly, enabling key duplication without requiring any additional tools. It supports the following unencrypted BDC3 key types: For encrypted BMW keys (BDC2, BDC3 with long chip, and […]
Xhorse Multi Prog MCU Adapter Modification Method
One customer gave feedback that he used Xhorse Multi Prog to read a 9S12HZ512 MCU, and the software asked him to modify MCU Adapter. If you have the same issue, follow the method below to modify adapter. Adapter before modification: Multi-Prog MCU Adapter originally has the following pin-to-cable connections: 1-VDD 2-GND Short 3-GND Long 4-VPP […]
Xhorse Update BMW BDC2 BDC3 BCP Encrypted Key Cloning
Xhorse official released a new BMW upgrade for Multi-PROG and VVDI Key Tool Plus. Update Info: Support BMW BDC2 / BDC3 / BCP Encrypted key cloning/copying Support Soldering Support VVDI BMW dedicated adapter Simple guide: Use Xhorse Multi Prog or Key Tool Plus to read BDC2 BDC3 encrypted key data Then write key by Xhorse […]
How to Solve Xhorse Audi BCM2 Adapter V2 PIN Connection Detect Failed?
One customer reported that when he used Xhorse Audi BCM2 Adapter V2 to work with Multi Prog, the reset terminal could not be recognized and appeared “PIN Connection Detect Failed” error message. Xhorsetool.com engineer offers the solution below: Modify Xhorse Audi BCM2 Solder-free Adapter V2 and retry again. XDNP100 BCM2-ADAPTER-A: XDNP101 BCM2-ADAPTER-B: Tech support: Email: […]
How to Fix Xhorse Multi Prog BMW FRM3 Chip Configuration Failed?
Reported Issue: An attempt to repair a BMW E-series FRM3 footwell module using Xhorse Multi Prog was unsuccessful. The process failed with the error: “Chip configuration failed. Error code 88030201: crystal frequency does not match.” Resolution: The issue was resolved by double-checking the hardware connection. The root cause was identified as an insufficiently soldered RESET […]
2002 Mercedes S500 (W220) AKL with Multi-Prog and Key Tool Plus OK
Xhorse tools successfully resolve all-keys-lost scenario on 2002 Mercedes S500 (W220). Vehicle: 2002 Mercedes-Benz S500 (W220) Case: All Keys Lost Solution Achieved Using: Xhorse Multi-Prog & VVDI Key Tool Plus Procedure Overview: 1.Data Extraction: Successfully read the immobilizer data from the EEPROM chip using the Xhorse Multi-Prog programmer. 2.Cloud-Assisted Decoding: Transferred the dump file to […]
Xhorse Update BMW G/U Series BDC3/BCP Key Copy Feature
Xhorse has released a significant firmware upgrade, introducing key cloning functionality for BMW G/U chassis vehicles equipped with BDC03 and BCP systems. This enhancement provides users with expanded capabilities for BMW key programming. License & Activation Requirements The BDC3 key cloning feature is automatically available to all users with an active BMW G BDC2 license—no […]
Xhorse Multi-Prog KIA MEG17.9.12 “Connection Failed” Solution
One customer gave feedback that when he used Xhorse Multi-Prog Programmer to read and write KIA MEG17.9.12, an error message “Connection failed” appeared on the screen. Xhorsetool.com engineer gave the suggestion below: This prompt indicates that there is no communication at all. Please try to operate in boot mode. Tech support: Email: sales@XhorseTool.com WhatsApp: +86 […]
