Xhorse Multi-Prog
How to Solve Xhorse Multi Prog “WiFi Module Not Inserted”?
Here is the solution for “WIFI Module Not Inserted” Error on Xhorse Multi Prog Programmer. The solution: This device supports built-in Wi-Fi connectivity. A USB Wi-Fi network adapter is included in the package.To enable Wi-Fi: Insert the USB Wi-Fi adapter into the port on the back of the machine. Power on the Multi-Prog The […]
How to Solve Xhorse Multi Prog Server Calculation Error (FFFF000C)?
Problem: When attempting to read a VAG SID10.4 ECU using the Xhorse Multi Prog, the operation fails and displays the error: “Server Calculation Error FFFF000C” The Solution: Check Your Network Connection Ensure you have a stable and active internet connection. A poor connection can prevent communication with the Xhorse server. Check Server Status The error […]
How to Solve Xhorse Multi Prog “Remaining Usage of the Device” Error?
One customer gave feedback that his Xhorse Multi-Prog Programmer appeared an error “The remaining usage of the device is less than 50 times.” Xhorsetool.com engineer offered the solution below: After using the Multi Prog for 1000 times, you need to synchronize the device again. Select Update Online >> Authorization management Sync device. Then the problem […]
Xhorse Multi Prog Fixes Audi Radio 24C256 Unit Component Protection
A customer tried to install a used Audi radio unit from eBay, only to be hit with the dreaded Component Protection (CP). Like many, he believed it would be plug-and-play—but reality had other plans. After unsuccessful attempts with various CG programmers and efforts to manually transfer EEPROM data, the solution finally came from Xhorse Multi-Prog […]
Xhorse Multi-Prog Clone Audi A3 (2014-2020) Climate Control Unit
Just wrapped up an interesting job cloning a climate control unit from an Audi A3 (2014, fits 2012-2020 models) and wanted to share the process using the Xhorse Multi-Prog Programmer. This is a great alternative for those without access to expensive tools like ODIS online, and it’s perfect for recycling spare parts from damaged vehicles. […]
(Solved) Xhorse Multi Prog Write BMW FEM BDC Chip Data Failure
One customer gave feedback that he failed to write service mode bmw bdc 95128 using Xhorse Multi-Prog Programmer. He read the data ok but when he wanted to write, he got the message “Chip data writing failed! Error code: 11030001”. The Xhorsetool.com engineer asked him to change the power settings. Customer feedback: Thanks so much! […]
How to Solve Xhorse Multi Prog Read BMW MSV80 “Number of Times is 0”?
Problem: When attempting to read a BMW X3 Continental MSV80 ECU using Xhorse Multi Prog, the following error appears: “The number of times used is 0.” Solution: This issue occurs because the daily limit for reading these DMEs has been reached. To resolve it: 1.Sync the Device: Navigate to Update Online→ Authorization Management Click Synchronizeto refresh […]
How to Solve Xhorse Multi Prog Update Firmware Error “Device Authentication Failed”?
One customer gave feedback that he failed to update the firmware of Xhorse Multi-Prog Programmer. He got two error messages below: Error 1: Device Authentication Failed. Error 2: The device is in Recovery mode and must undergo a firmware upgrade before use. The solution: Press and hold the RST button for 5 seconds before connecting […]
Xhorse Multi Prog Renault Master BCM N3 D70F3376A Pinout
Xhorse Multi Prog can support Renault Master BCM N3 D70F3376A reading and writing. Here share the pinout for reference. In the Multi-Prog software, select MCU-Renesas-V850- D70F3376A www.xhorsetool.com
How to Solve Xhorse Multi-Prog Stop Upgrading Problem?
One customer reported that his Xhorse Multi-Prog was stuck in the upgrade process. Xhorsetool.com engineer offered the solution below: Press and hold the RST button for 5 seconds before connecting the power adapter to power on, and then release to update the firmware again NOTE: Do not release RST button before starting up, and do not release […]
How to Use Xhorse MVCI PRO J2534 for Vehicle Diagnosis and Programming?
In this guide, we’ll walk you through the steps to use the Xhorse MVCI PRO-J2534 for vehicle diagnostics and programming. This tool is compatible with various vehicle models, including Volvo, Nissan, Mazda, Toyota, and Honda. Follow these steps to get started: Download the MVCI PRO-J2534 Software http://dl.xhorse.net.cn/product/mvci/MVCI_PRO-J2534_1.0.3.exe Install the MVCI PRO-J2534 Driver Follow the installation steps provided. […]
