Xhorse Multi Prog Tag Archive
How to Solve Multi Prog Update Firmware “Jump Recovery Error 41330004”?
Reported Problem: A user recently installed Xhorse Multi Prog on his PC but ran into trouble when trying to update the firmware from version 1.36 to 1.45. The upgrade failed with the error: “Jump Recovery error: Error code: 41330004 fails to communication with the SC chip.” Recommended Solution: You can attempt a forced firmware upgrade […]
Xhorse Multi Prog Update BDC3 Key Copy Function
Xhorse Multi Prog‘s new V87 database (released Dec. 2, 2025) introduces a streamlined process for BMW BDC03 keys. Update Highlights: Optimized BMW BDC03 key programming Direct read/write of original factory keys No data conversion required Result: Clone BMW BDC3 keys without using VVDI2 or Key Tool Plus. www.xhorsetool.com
How to Solve Xhorse Audi BCM2 Adapter V2 “PIN is Abnormal”?
Problem: One customer gave feedback that his Xhorse Multi Prog with Audi BCM2 Adapter V2 failed to read an Audi BCM2 3381 version. The tool repeatedly returned a “pin is abnormal” error, but the older BCM2 adapter v1 worked correctly on the same module without any issues. Solution: Modify Xhorse Audi BCM2 Solder-free Adapter V2 […]
Xhorse Multi Prog & VVDI Prog BMW FRM2 ST10F269 Pinout
Here shares the BMW FRM2 (Footwell Module) ST10F269 Pinout for Xhorse Multi Prog &VVDI Prog. For Xhorse VVDI Prog and Multi-Prog: To reprogram your BMW Footwell Module (FRM), you must use the appropriate flash and EEPROM files that match your specific module version. It is important to know that a complete module recovery is only […]
Xhorse Multi-Prog Clone Audi BCM2 Module Guide
Whether the Audi BCM2 module can be cloned using Xhorse Multi Prog or VVDI Key Tool Plus? The answer depends on having the correct hardware and understanding the module’s encryption status. Adapter Requirement: ❌ Not possible with the old BCM2 adapter (with yellow power adapter) — it cannot read full EEPROM and flash data. ✅ […]
How to Solve Xhorse Multi Prog “WiFi Module Not Inserted”?
Here is the solution for “WIFI Module Not Inserted” Error on Xhorse Multi Prog Programmer. The solution: This device supports built-in Wi-Fi connectivity. A USB Wi-Fi network adapter is included in the package.To enable Wi-Fi: Insert the USB Wi-Fi adapter into the port on the back of the machine. Power on the Multi-Prog The […]
How to Solve Xhorse Multi Prog “Remaining Usage of the Device” Error?
One customer gave feedback that his Xhorse Multi-Prog Programmer appeared an error “The remaining usage of the device is less than 50 times.” Xhorsetool.com engineer offered the solution below: After using the Multi Prog for 1000 times, you need to synchronize the device again. Select Update Online >> Authorization management Sync device. Then the problem […]
Xhorse Multi Prog Fixes Audi Radio 24C256 Unit Component Protection
A customer tried to install a used Audi radio unit from eBay, only to be hit with the dreaded Component Protection (CP). Like many, he believed it would be plug-and-play—but reality had other plans. After unsuccessful attempts with various CG programmers and efforts to manually transfer EEPROM data, the solution finally came from Xhorse Multi-Prog […]
(Solved) Xhorse Multi Prog Write BMW FEM BDC Chip Data Failure
One customer gave feedback that he failed to write service mode bmw bdc 95128 using Xhorse Multi-Prog Programmer. He read the data ok but when he wanted to write, he got the message “Chip data writing failed! Error code: 11030001”. The Xhorsetool.com engineer asked him to change the power settings. Customer feedback: Thanks so much! […]
How to Solve Xhorse Multi Prog Read BMW MSV80 “Number of Times is 0”?
Problem: When attempting to read a BMW X3 Continental MSV80 ECU using Xhorse Multi Prog, the following error appears: “The number of times used is 0.” Solution: This issue occurs because the daily limit for reading these DMEs has been reached. To resolve it: 1.Sync the Device: Navigate to Update Online→ Authorization Management Click Synchronizeto refresh […]
How to Solve Xhorse Multi Prog Update Firmware Error “Device Authentication Failed”?
One customer gave feedback that he failed to update the firmware of Xhorse Multi-Prog Programmer. He got two error messages below: Error 1: Device Authentication Failed. Error 2: The device is in Recovery mode and must undergo a firmware upgrade before use. The solution: Press and hold the RST button for 5 seconds before connecting […]
