Condor XC-Mini Plus

Xhorse Condor XC-Mini PLUS (New)

Xhorse Condor Mini Plus testing: Note that it will replace the Condor Mini key cutting machine. Tech support from http://www.xhorsetool.com/

Read More

Uncategorized

BMW 520D 2012 F10 CAS4 Adds A New Key by VVDI Tools

Confirmed! VVDI2 and VVDI-Prog successfully add a new key to Bmw 520d 2012 f10 body cas4.  

Read More

VVDI Key Tool

VVDI Key Tool can copy VW 48 96 bit chip

Success! Xhorse VVDI Key Tool is confirmed to copy VW 48 96 bit transponder. It’s very easy to collect data of the original key and then upload data to write to the new chip. That’s all. Here is the how-to’s in detail. The VVDI Keytool and app on an Android device, the key.. The dash Note: All […]

Read More

Xhorse VVDI2 Key Programmer

Xhorse VVDI2 Update to V5.5.0

VVDI2 latest software version V5.5.0 update: Softwar download:https://goo.gl/UgLBJ8 *** 2018-05-15 *** Require firmware V5.5.0 ************************************************* ********************* ===== VAG V5.5.0 ===== 1. Add support for 2012-2014 MQB(Continental/VDO) immobilizer and mileage. Support following cars: a. VW Golf7 (2012-2014) b. Skoda Octavia3 (2012-2014) c. Audi A3 (2012-2014) d. Seat Leon (2012-2014) 2. Bugfix for old bentely (2006 kline) […]

Read More

Uncategorized

How to combine VVDI2 and VVDI Key Tool

Look here: How to combine Xhorsevvdi2 and key tool Need to open the VVDI2 software and click on the transponder programmer option. Then along top menu bar, click ‘points system’ and you will find an option to enter your key tool serial number and bind the two devices while both connected to the computer. This means […]

Read More

VVDI Key Tool

How to collect Volvo ID48 data with VVDI Key Tool

Volvo model is special for collect data from switch, usually the ignition signal for acquisition every 15mins will change one time. such as:if you use VVDI KEY TOOL to collect data within 5mins several times, you will get stuck at 1/8 collect data. have to wait around 15mins later then do next time collect data, […]

Read More

VVDI Key Tool

(Review) VVDI Key Tool Copy ID46 Chip: Success

VVDI Key Tool Review: copy id46 chip ….   first read the chip then press clone and sniff data from ignition coil then you will be asked to put the original key inside the induction coil for calculating key data. *be careful when calculating because the tool can’t calculate key data if the key is not […]

Read More

VVDI MB BGA Tool

VVDI MB does 2009 C300 (W204) all keys lost via OBD?

Question: Can VVDI MB Tool do 2009 C300 (w204) all keys lost via OBD? Answer: No, only on bench   In detail….   Step 1: remove eis from car: Disconnect battery cause you gotta remove airbag , then remove steering wheel and then you will able to remove ezs   Need to take eis read on […]

Read More

Xhorse VVDI2 Key Programmer

Is there VAG UDS cluster cable for VVDI2?

No, but you can use any aftermarket UDS cable to power up and connect CAN communication between VVDI2 and your UDS cluster.   If you’re referring to the pogo pin cable which bypasses flash security for easy service mode without removal of Eeprom, this is only found on Advanced Diagnostics equipment, IEA Zedfull and Supervag […]

Read More

VVDI Key Tool

Vvdi key tool can copy Passat id48 key

Vvdi key tool can copy id48 Passat key. 25 min calculation time! Btw, program remote with Obdstar x300dp pad

Read More

Xhorse Key

Steps to put VVDI BE Key PCB into smart key shell

Here are steps to assemble VVDI BE Key PCB with the Smart Key Shell 3 Button for Mercedes Benz: 1. Put the VVDI BE key Pro improved version PCB into the case. 2. Cover the bottom case. 3. Insert the battery and cover the case. 4. Push the metal strips on both sides into the right position. 5.Here rearmetal […]

Read More

Copy Protected by Chetan's WP-Copyprotect.